Loba Easy Finish Gloss Gallon

Product Description

1K water-based finish. Easy application at the performance of a 2K system. Unique in its class!

LOBADUR^® EasyFinish has been inspiring contractors and end users in over 60 countries for many years. The outstanding application features and strong performance combine LOBADUR^® EasyFinish to set the absolute benchmark
among 1-component water-based finishes. Enthusiastic contractors and countless pleased end-consumers speak for themselves year after year.

• Long-lasting beauty of the floor – high resistance to mechanical wear and household chemicals
• Custom choice of appearance – available in satin, semi-gloss and gloss
• Simple and convenient care and maintenance
• Non-Yellowing
• Time saving – light use after 24 hours, fully cured after only 5 days
• Easy 1K system combined with 2K performance
• Outstanding application qualities – easy to use and safe, no lap marks
• No mixing - no pot life - no waste
• Excellent build through high solid content
• Suitable for almost all wood species as well as cork
• Very low emission, EMICODE^® EC1

Special Features:

Take it easy – LOBADUR^® EasyFinish is known for its outstanding application qualities. In combination with the water-based filler EasyFillPro and the universal sealer/primer EasyPrime, contractors benefit from the highest level of safety and performance!

Recommended use:

Suitable for wood and cork floors. For heavy traffic residential areas and light traffic commercial use.

Packaging:

Case: 4 x 1 US gallon plastic bottle
Pallet: 200 x 1 US gallon plastic bottle

Coverage:
500-600 square feet per gallon

Recommended conditions for application:
55°F-80°F/40-75%rH.

Application:

• Sand and remove dust from the surface properly
• The use of a primer is recommended (e.g. LOBADUR® EasyPrime). Make sure you allow it to dry properly.
• First coat of EasyFinish with LOBATOOL roller Microfibre 100-120 (or T-bar, Trim Pad, Lambswool, Brush)
• Allow to dry for 2-3 hours
• Intermediate sanding with 150 grit
• Second coat of EasyFinish with LOBATOOL roller Microfibre 100-120 (or T-bar, Trim Pad, Lambswool, Brush)

ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY, APPEARANCE, AND DESIRED RESULTS.

• Shake material well before use.
• Do not thin. Do not add water.
• Do not apply at temperatures below 55°F (13°C). Make sure material is at room temperature. Always maintain adequate ventilation during all phases of the coating and drying process.
• Apply evenly at the recommended coverage rate. Avoid streaks, puddles, and lap marks.

Application Tools:

• LOBA Micro 120 Roller
• T-bar
• Trim pad
• Lambswool
• Brush
• Roller

Screen and Recoat:

• Clean floor, abrade with LOBASAND 180-220 grit perforated pad(or equivalent). Vacuum floor then tack using a LOBA Mop and a new/clean LOBA microfiber mop pad lightly dampened with water to remove all dust.
• Apply finish following instructions.
• Always prepare test areas to determine compatibility, appearance, and desired results.
• Do NOT use on floors finished with UV cured, oxide containing, factory applied finishes.

Drying Time:

• Earliest possible recoating after 2-3 hours.
• Fully cured after 5 days.
• If there is a delay in drying wait until you can see that the surface is completely dry.

Recommended Procedure for Cork Floors:

• Seal cork only after the glue has sufficiently set (refer to manufacturer’s information) Roll on a maximum of 2 coats per day
• Untreated natural cork:
  • Roll a total of three coats of finish onto the cork.
  • Apply first coat and allow to dry 2-4 hours.
  • Apply the second coat and allow to dry overnight (reduces risk of granule swelling).
  • Intermediate sanding with LOBASAND 180-220 perforated pad (or equivalent) to remove grain raise. Vacuum floor then tack using a LOBA Mop and a new/clean LOBA microfiber mop pad lightly dampened with water to remove all dust.
  • Apply final coat.
• Prefinished cork:
  • Note information given by the cork supplier. If suitable for recoating, apply one or two layers of coating after an intermediate sanding.

Renovation / recoating of old coatings: Basic cleaning with Remover

• Use a rotary disk buffing machine and a LOBASAND SpecialPad green.
• Care product residues must be completely removed. Even small amounts of residue can adversely effect the bond of the coating. Clean with clear water (neutralize).
• After drying, perform a thorough intermediate sanding or preparation with LOBA 2k Contact.
• Apply coating in one or two layers by roller

Compatability:

When this product is used in combination with other LOBA products the technical information of these products must be followed. Refer to the Technical Data Sheets. LOBA cannot guarantee the suitability of products other than LOBA.

Cleaning of tools:
Clean tools and equipment with water.

Cure Time:
The stated drying and cure times are based on ideal conditions (68°F, 50% rH) at the recommended application rates. Insufficient ventilation, high humidity, lower temperatures, increased coat thickness can prolong the curing process considerably. Do not cover floors, replace carpets or rugs, or clean floors with a damp mop/cloth before the final curing has been reached.

Intermediate sanding:
When several layers of finish are being applied succesive coats can be applied within 24 hours without intermediate sanding. After 24 hours an intermediate sanding must be performed. An intermediate sanding before the final application is recommended and will achieve a smoother surface. Remove all dust after intermediate sanding and prior to application of finish coats.

Use with or without a primer:
Some finishes can be used without a primer. The use of a primer increases application reliability and decreases risk of application marks on most wood types. Further details can be found in the LOBA wood type suitability list in the current catalog.

Side bonding:
Water-based coating systems can show a tendency for side bonding. Several measures can be taken to minimize the formation of irregular joints and the associated locking effect. The use of shear-resistant or firm elastic adhesive to adhere the hardwood flooring, careful filling of the joints, use of suitable LOBA primers, and maintaining a consistent climate are some of these steps. (Education of the customer is recommended). The risk of side bonding is greater with old floors with damaged, weak, or very flexible adhesives and wood flooring installed over underfloor heating, and less stable woods such as beech and maple.

Safety Precautions:
Even when working with low or zero-emission products the usual safety measures must be taken. Keep away from children. Do not eat, drink, or smoke in working areas. Wear suitable safety gloves. Clean product off of hands. Change soiled clothes. EasyFinish satin First Aid: If swallowed, do not induce vomiting. Call for medical help immediately. Never give anything by mouth to an unconscious person. If breathing is difficult or other respiratory complaints, remove to fresh air and get medical attention. In case of eye contact, immediately flush eyes for several minutes under running water. Generally, this product does not cause skin irritation. Call a physician if irritation occurs.

Special Information:
The information in this document and any other information or advice we provide is intended for customers only, and all information and advice is subject to the terms and limitations in Loba-Wakol’s General Terms and Conditions, including without limit its limited warranty (“Terms”). The Terms are not expanded, changed, or waived by the information in this document or by any information or advice given by Loba-Wakol. Loba-Wakol has no relationship or obligation to anyone other than the customer that originally purchases the product from Loba-Wakol. The information in this document and any other information or advice we provide is the result of our prior experience and our knowledge of our products. Due to the wide variety of application possibilities and processing conditions, it is the customer’s responsibility to test our product for suitability for its intended purpose. When in doubt, call Loba Technical Service for support. If you have any questions during application or use, immediately stop the application and use and contact our Technical Service. For information about other products offered by Loba-Wakol, please check the technical information concerning those products.

Connected Systems:
Connected Systems approved products are optimized in such way that no dark discoloration, caused by chemical interaction between finish and adhesive occurs, when applied in accordance with the Technical Information.